ROJES2XT(usermod MRO6029)をアセンブル・リンク後、どのようにJESにインストールすればよいのですか?

Document created by Kenji_Tsuda Employee on Jul 2, 2015
Version 1Show Document
  • View in full screen mode

文書番号:JTEC001533

製品名:CA Roscoe

バージョン:R6.0

OS:z/OS

 

Question

ROJES2XT(usermod MRO6029)をアセンブル・リンク後、どのようにJESにインストールすればよいのですか?

 

Answer

ROJES2XTは、Prefix.RO60LIBからリンクリストに含まれるライブラリへ移動する必要があります。 その後、JESPARMSを以下のように変更します。

 

     LOADMOD(ROJES2XT) STORAGE=CSA

     EXIT(5) ROUTINE=(RO$EXIT5),STATUS=ENABLED,TRACE=NO

       

複数のEXITが存在する場合、RO$EXIT5が先頭になる必要があります。 そして、次回システムでIPLが実施される際、EXITがロードされます。

 

注: OS/390 2.4.0以上およびJES 2.4.0以上を使用している場合は、ROJES2XTはgenlevel 9812以上であることを確認する必要があり、それより古いgenlevelを使用している場合 『JES2 CATASTROPHIC ERROR』 が発生する可能性がありますのでご注意ください。

以下は、弊社Webサイト(http://support.ca.com/)からもご確認いただける 『JES2 CATASTROPHIC ERROR』 に関する情報です。 

 

 

                 Title: A JES2 CATASTROPHIC ERROR WILL OCCUR IN JES2

 

        PRODUCT: CA-ROSCOE-MVS                           RELEASE: 6.0

        PEA #:   LI90907                                 DATE:    20 MAR 2001

 

                        *****   Product Error Alert   *****

 

  PROBLEM DESCRIPTION:  A JES2 catastrophic error will occur in JES2 Versions 2.4.0 and

                        above if the incorrect version of the ROJES2XT is installed in JES.

                       ---------------------------------------------------------------------

 

  HYPER: NO

  DISTRIBUTION CODE: A (A=AVAILABLE, I=INTERNAL)

  PROBLEM RESOLUTION:

 

   Clients using OS/390 2.4.0 or above and JES 2.4.0 or above must verify that ROJES2XT

  is genlevel 9812 or above.  Failure to do so could cause catastrophic errors in JES.

 

   Installing the ROJES2XT correctly is critical to running CA-Roscoe in a JES2 environment.

 

   The ROJES2XT must first be assembled and linkedited following the instructions in the

  usermod MRO6029.   Please verify that the syslib concatenation is in the following

  sequence before assembly.

            1.   SHASMAC

            2.   RO60MAC

            3.   SYS1.MACLIB

            4.   SYS1.MODGEN

 

   After you assemble and link ROJES2XT, move it to a linklisted data set, and update the

  JESPARMS as shown below.

 

            LOADMOD(ROJES2XT) STORAGE=CSA

            EXIT(5) ROUTINE=(RO$EXIT5),STATUS=ENABLED,TRACE=NO

 

            NOTE: The exit routine name (RO$EXIT5) must not be changed

 

   If there are multiple exits, the ROJES2XT must be specified first in the exit list as

  shown in the following example:

 

            LOADMOD(ROJES2XT) STORAGE=CSA

            LOADMOD(xxxxxxxx) STORAGE=***

            EXIT(5) ROUTINE=(RO$EXIT5,xxxxxxxx),STATUS=ENABLED,TRACE=NO

 

            NOTE: The exit routine name (RO$EXIT5) must not be changed to initialize or

                  reload the exit, JES2 must be warm started, or the system must be ipled.

 

   Please refer to Section 11.5 of the CA-Roscoe System Reference Guide for further

  information.

 

   You can display the JES2 Exit Point Status by issuing the JES2 command:

            $D EXIT5

 

   You can display the ROJES2XT by extering the JES2 command:

            $D MOD(ROJES2XT)

 

   Please refer to the IBM JES2 Commands manual for more information on the JES2 commands

  described above.

 

   Thank you for your continued support of Computer Associates and its products. If you

  have any questions about this Product Information Bulletin or any other questions

  about this product,  please contact your local Computer Associates Technical Support

  organization.

 

  PRODUCT(S) AFFECTED: CA-ROSCOE-MVS                          RELEASE  6.0

                       CA-ROSCOE/DB2-MVS                      RELEASE  6.0

Attachments

    Outcomes