ca.portal.admin

Separate WTOEXIT

Discussion created by ca.portal.admin on Dec 2, 2008
Latest reply on Dec 3, 2008 by ca.portal.admin
I'm trying to get my shiny new 17.0 system to load a separate WTOEXIT =
with the WTO=3DWTOEXIT parameter. I can't get it to work. It always says =
that the module is not found. Any tips?
=20
______________________________________________________________
=20
Chris Trayler, IXD
Bank Julius Baer & Co. Ltd.
P. O. Box, CH-8010 Z=FCrich, Switzerland
Telephone +41 (0)58 887 4332, Fax +41 (0)58 887 4969
www.juliusbaer.com <http://www.juliusbaer.com/>=20
=20
______________________________________________________________
=20
*****JuliusBaer Disclaimer***** This e-mail is for the intended =
recipient only and may contain confidential or privileged information. =
If you have received this e-mail by mistake, please contact us =
immediately and completely delete it (and any attachments) and do not =
forward it or inform any other person of its contents. If you send us =
messages by e-mail, we take this as your authorization to correspond =
with you by e-mail, however, we will not accept the electronic =
transmission of orders/instructions without a specific agreement being =
in place to govern the same. If you do not wish to receive any further =
e-mail correspondence please let us know. E-mail transmission cannot be =
guaranteed to be secure or error-free as information could be =
intercepted, amended, corrupted, lost, destroyed, arrive late or =
incomplete, or contain viruses. Neither the Julius Baer Group nor the =
sender accept liability for any errors or omissions in the content of =
this message which arise as a result of its e-mail transmission. Please =
note that all e-mail communications to and from the Julius Baer Group =
may be monitored. This communication is for informational purposes only. =
It is not intended as an offer or solicitation for the purchase or sale =
of any financial instrument or as an official confirmation of any =
transaction.
"
IDMS 3rd-party providers forum
IDMSVENDOR-L@LISTSERV.IUASSN.COM
SMTP
IDMSVENDOR-L@LISTSERV.IUASSN.COM
IDMSVENDOR-L@LISTSERV.IUASSN.COM
SMTP








Normal

Normal
Re: Separate WTOEXIT
"If you have two loadlibs, a steplib and cdmslib, I'd put it in both=2E=0D=
=0AAlso, make sure it's the module name not the entry name that resides in=
=0D=0Ayour loadlib=2E I'd copy the loadmodule to one that's got the same n=
ame=0D=0Aas the entry point=2E=0D=0A=0D=0ALutz Petzold=0D=0ATDM UDB/IDMS Su=
pport=0D=0A401-782-2265=0D=0APage 860 366 0865 or Telalert=0D=0A =0D=0A =0D=
=0A=0D=0AThis e-mail may contain confidential or privileged information=2E =
If=0Ayou think you have received this e-mail in error, please advise the=0A=
sender by reply e-mail and then delete this e-mail immediately=2E=0AThank y=
ou=2E Aetna
"
IDMS 3rd-party providers forum
IDMSVENDOR-L@LISTSERV.IUASSN.COM
SMTP
IDMSVENDOR-L@LISTSERV.IUASSN.COM
IDMSVENDOR-L@LISTSERV.IUASSN.COM
SMTP








Normal

Normal
Re: Separate WTOEXIT
"If you have two loadlibs, a steplib and cdmslib, I'd put it in both.
Also, make sure it's the module name not the entry name that resides in
your loadlib. I'd copy the loadmodule to one that's got the same name
as the entry point.

Lutz Petzold
TDM UDB/IDMS Support
401-782-2265
Page 860 366 0865 or Telalert



This e-mail may contain confidential or privileged information. If
you think you have received this e-mail in error, please advise the
sender by reply e-mail and then delete this e-mail immediately.
Thank you. Aetna
"
IDMS Public Discussion Forum
IDMS-L@LISTSERV.IUASSN.COM
SMTP
IDMS-L@LISTSERV.IUASSN.COM
IDMS-L@LISTSERV.IUASSN.COM
SMTP








Normal

Normal
Re: Separate WTOEXIT
"Chris. It has to be one of two possibilities.
1) The LOAD module must be named WTOEXIT if your parm says WTO=WTOEXIT
2) The loadlib containing module WTOEXIT must be in the STEPLIB concatenation.

3?- If you get online and do a LOOK PROGRAM=WTOEXIT it will tell you what DSN (loadlib) it was loaded from. That MUST be in the STEPLIB concatenation.

Ed McKinney
CA-IDMS

Outcomes